20 November, 2026
How to Install a Toilet Flapper (Outlet Washer) and Stop the Leak
Find out how to install toilet flapper parts, check the inlet valve, and test your flush, plus know when to call a licensed plumber.
That constant trickle into the toilet bowl at 2am? Annoying, isn't it. Here's the thing though — nine times out of ten it's just a worn-out flapper (the rubbery bit at the bottom of the cistern), and in some states, such as Queensland and Western Australia, you can sort it yourself without calling anyone. The fix is simple: shut off the isolation valve, swap the old flapper for a new WaterMark-certified one, then test the flush. Honestly, once the water's off, the replacement usually takes around fifteen to twenty minutes, tops. No fancy tools required — just a spanner, a towel, and a bit of patience with the fiddly chain hook; in states such as NSW and Victoria, or if the whole outlet valve needs replacing, call a licensed plumber.
Video Credit: Roger Wakefield Plumbing Education
What is a flapper (outlet washer) and why does my toilet leak?
Chances are you've probably been dealing with a leaking toilet for a while now. The culprit is likely a faulty toilet flapper (also called outlet washer). This is what you see at the bottom of the cistern and allows water to flow into the bowl when you flush the toilet.
It's a simple piece of rubber or plastic that raises to allow water to flow out of the cistern. After some time, the flapper may become warped or damaged, which causes water to constantly run from the cistern into the bowl.
The good news is that this is a pretty easy fix and doesn't require any special skills, but first, we have to understand how toilet flappers work. The bad news is that this issue is generally silent, and if your toilet is making a hissing noise, it's a signal that the inlet valve is faulty and should be replaced, but that's beyond the scope of this article.
The flapper is usually the issue, and you don't need to be a master plumber to install toilet flapper replacements. Let us walk you through the process.

Tools and Parts You'll Need Before You Start
Before we begin, you'll need to gather the following supplies: Adjustable spanner Old towel Small bucket New outlet washer (flapper)
It's also essential that you get the right size of outlet washer. Flappers (outlet washers) on toilets vary depending on the toilet type and brand, so it's best to either photograph the old one before removing it, or take it with you to the store to ensure you're purchasing a compatible replacement. When you're out looking for a replacement flapper, make sure it has WaterMark certification (WaterMark Certification Scheme). This shows that the product has been tested to ensure it is safe to be used in Australia.
Once you have all the tools, you're ready to start!

How to replace a toilet flapper
Find the toilet's isolation valve, which is usually located behind or beside the toilet, and close it. If the valve will not budge, or starts to leak when you try to close it, stop there and call a licensed plumber. If it moves smoothly, then continue to the next step.
Next, flush the toilet to empty the tank, and use your towel to wipe up any excess water in the tank.
Remove the cistern lid and set it aside somewhere secure (gyprock walls and shattered porcelain lids are not friends, trust me). Remove the old flapper (outlet washer) from the flush valve seat, and unhook it from the flush mechanism above.
To install toilet flapper number two, just put it over the top of the seat so it's sitting nicely and flat in the centre, then connect it to the lift arm or chain as instructed by the installation instructions that came with your toilet, because not all toilets are the same.
Tug gently on it to check that it lifts freely and drops back into place without any snagging. Once the water is shut off, the replacement usually takes around fifteen to twenty minutes.
Now that you've taken the lid off the cistern and replaced the flapper, you might as well inspect some of the other components around the cistern.

Checking the Inlet Valve and Cistern Seal While You're In There
The inlet valve, which is the part that fills the cistern each time you flush, is worth checking too. If it sounds like it's hissing or taking a long time to fill, or there's a continuous flow of water into the overflow pipe, then you may have a bad inlet valve. This is another common cause of leaking toilets, but because it connects directly to the main water supply, you should leave the replacement to a licensed plumber.
Look closely at the toilet cistern seal (the gasket where the cistern meets the pan), too. Any signs of damage or leakage here are worth noting, although if it means removing the cistern entirely, this is a task you should leave to a licensed plumber, as removing the cistern and pan connector requires a licensed plumber under state and territory plumbing licensing legislation.
After you've inspected the other parts and confirmed they're okay, the last step is to turn the water back on and test your repair.

Testing the Flush and When to Call a Professional
Turn on the isolation valve and let the cistern fill up, then press the toilet flush button, preferring both full and half flush if you have a dual flush toilet. The water should sit below the level of the overflow pipe when you're done, and shouldn't be running after that.
If it's still dripping, the chain/lift arm may need adjusting so the flapper seals properly.
If it continues to leak after you install toilet flapper replacements, the isolation valve is seized/rusted shut, or the toilet cistern seal needs to be replaced at the pan connection, it's time to call a licensed plumber, as any bathroom plumbing work in Australia must be done by a licensed plumber (state and territory plumbing licensing legislation).
Otherwise, you've saved yourself a service call and used less water along the way.
References
WaterMark Certification Scheme, Australian Building Codes Board
AS/NZS 3500.2:2025 Plumbing and Drainage — Sanitary Plumbing and Drainage, Standards Australia
State and territory plumbing licensing authorities (Building and Plumbing Commission Victoria; Building Commission NSW / NSW Fair Trading; Queensland Building and Construction Commission; Plumbers Licensing Board Western Australia (administered by Building and Energy); Consumer, Building and Occupational Services Tasmania; Access Canberra ACT; Office of the Technical Regulator / Consumer and Business Services South Australia; Plumbers and Drainers Licensing Board Northern Territory)


